Getting Familiar with Plumbing: Your Starting Point for When Installing a Bathtub
Getting Familiar with Plumbing: Your Starting Point for When Installing a Bathtub
Blog Article
We've stumbled upon this article relating to A Step-by-Step Guide to Installing a Bathtub down the page on the web and accepted it made sense to share it with you on this page.
Mounting a tub isn't exactly brain surgery, but it does call for solid plumbing, woodworking, as well as sometimes, tiling abilities. Replacing an old tub with a new one is likewise a moderately tough project. If the old bathtub is readily easily accessible, the project can relocate rapidly; if you need to open up a wall to eliminate the old bathtub and place the brand-new tub, the task is much harder. In either case, the task is within a residence handyman's abilities, although you will certainly need a helper to move out the old bathtub and also embeded in the new one. See to it you have actually qualified on your own for the job and also are comfortable attempting it. As opposed to working with a professional to take control of a halfway-completed project, it is much better to think about utilizing one before you start. Opportunities are you might need a professional plumber to make tube links.
This post will aid you set up a new bath tub in your washroom if you have currently gotten a new bathtub and do not need to transform the arrangement of your previous water supply pipes.
Your devices as well as product checklist must comprise the following:
Removing Old Touches
If you require to replace old faucets with new ones as a part of your installment, after that the first thing you ought to do is disconnect the water. After doing so, turn on the faucets to drain any kind of water staying in the system. The procedure of removing the existing faucets can be quite problematic as a result of the restricted gain access to that is usually the case.
Make use of a basin wrench (crowsfoot spanner) or a tap device to reverse the nut that links the supply pipes to the faucets. Have a towel prepared for the remaining water that will certainly originate from the pipes. As soon as the supply pipes have been gotten rid of, utilize the same device to loosen the nut that holds the faucets onto the bath/basin. You will require to stop the solitary taps from transforming during this procedure. Once the taps have actually been eliminated, the holes in the bath/basin will certainly have to be cleaned up of any kind of old sealing substance.
Before carrying on to fit the brand-new taps, compare the pipeline links on the old taps to the new faucets. If the old faucets are longer than the new faucets, then a shank adapter is needed for the brand-new taps to fit.
Fitting New Taps
If the tails of the new faucets are plastic, then you will require a plastic port to prevent damage to the string. One end of the adapter fits on the plastic tail of the tap as well as the other end offers a connection to the current supply pipes.
If you require to fit a monobloc, after that you will certainly require lowering couplers, which connects the 10mm pipeline of the monobloc to the basic 15mm supply pipe.
Next off, place the tap in the mounting opening in the bath/basin making certain that the washing machines are in area in between the tap and also the sink. Protect the tap in position with the producer provided backnut. As soon as the tap is firmly in place, the supply pipelines can be linked to the tails of the faucets. The taps can either be attached by using corrugated copper piping or with typical tap ports. The previous type must be connected to the tap finishes initially, tightening up only by hand. The supply pipes can later on be linked to the other end. Tighten up both ends with a spanner after both ends have actually been connected.
Installing the Bath tub
Utilizing both wood boards under its feet, place the bath tub in the required placement. The wooden boards are useful in equally spreading the weight of the tub over the location of the boards rather than concentrating all the weight onto 4 little factors.
The following goal is to make sure that the bathtub is leveled all round. This can be attained by examining the level and adjusting the feet on the bath tub until the level reviews degree.
To mount faucets, fit all-time low of the furthest versatile tap adapter to the proper supply pipe by making a compression sign up with; then do the same for the various other tap.
Activate the water system and examine all joints and brand-new pipework for leaks and also tighten them if required. Load the bathtub as well as also inspect the overflow electrical outlet and the typical electrical outlet for leaks.
Lastly, deal with the bath paneling as explained in the supplier's instruction manual. Tiling and sealing around the bath tub should wait until the tub has actually been used at the very least once as this will certainly settle it right into its last position.
Preparing for the Installment
First of all, the sustaining frame supplied with the bath should be fitted (if required) according to the maker's directions. Next off, fit the faucets or mixer to the bathtub. When suitable the faucet block, it is important to ensure that if the tap includes a plastic washing machine, it is fitted between the bath as well as the faucets. On a plastic bath, it is also reasonable to fit a supporting plate under the taps unit to stop stress on the bathtub.
Fit the versatile tap ports to the bottom of the two faucets using 2 nuts as well as olives (in some cases provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet hole, and after that pass the electrical outlet through the hole in the bathroom. Make use of the nut supplied by the producer to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipe.
Next, fit the end of the versatile overflow pipeline to the overflow electrical outlet. After that, screw the pipeline to the overflow face which should be fitted inside the bath. See to it you utilize every one of the supplied washers.
Attach the trap to the bottom of the waste outlet on the bath tub by winding the string of the waste outlet with silicone mastic or PTFE tape, and also screw on the catch to the outlet. Attach the bottom of the overflow tube in a comparable manner.The bathroom should currently be ready to be suited its final placement.
Tiling Around the Tub
In the location where the bathroom satisfies the tile, it is required to seal the accompanies a silicone rubber caulking. This is essential as the fitting can relocate sufficient to split a stiff seal, causing the water to permeate the wall surface between the bathroom and the tiling, leading to complications with wetness and also feasible leaks to the ceiling below.
You can choose from a variety of coloured sealers to blend in your components as well as installations. They are sold in tubes and also cartridges, as well as can sealing spaces as much as a size of 3mm (1/8 inch). If you have a bigger void to load, you can load it with twists of soaked newspaper or soft rope. Remember to always fill the bathtub with water before sealing, to allow for the movement experienced when the bathtub remains in usage. The sealer can split relatively early if you do not consider this movement before securing.
Additionally, ceramic coving or quadrant ceramic tiles can be used to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as cut to dimension, are likewise easily readily available on the market. It is advisable to fit the floor tiles utilizing waterproof or water-proof glue and cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
We had been made aware of that report about A Step-by-Step Guide to Installing a Bathtub from a good friend on a different web blog. Kindly take the time to share this blog if you appreciated it. Thank you so much for taking the time to read it.
Trusted help? Ring now. Report this page